1994 Mazda RX-7 R2
Purchased used from orginal owner in Georgia in 11/98 - $19,200
James Auto Transport shipped to NH - $690
Auto Advantage Extended (5yr /50,000 miles) Warranty - $1495
| Mods | Vendor | Price |
| Engine mods: | ||
| PFS (EFI-systems) PMC and palm unit w/ release 9.1 software (pink edition) | Peter Farrell | |
| Software upgrade (v. 3.0) | Peter Farrell | 250 |
| M2 cold air intake w/ aluminum pipes & K&N air filters | ||
| M2 Race Intercooler w/ aluminum pipes | ||
| HKS supersequential BOV | Paisley Automotive | 401 |
| Efini Y-pipe | M2 Performance | 295 |
| RP Underdrive SuperPulleys | Rotary Performance | 250 |
| Bonez billet aluminum (8.5 lb.) flywheel | Rotary Performance | 499 |
| Bonez Street/comp Clutch | Rotary Performance | 500 |
| Clutch Bearing Kit | Rotary Performance | 60 |
| Jacobs Rotary Pro Pak ignition w/ | ||
| Jacobs 8.5 mm plugwires | Rotary Performance | 389 |
| Later Replaced to stock w/ 10mm Taylor Wires | ||
| Torquemaster plugs | 80 | |
| Odyssey battery (relocated in passenger's side bin) | ||
| J&S knock sensor and safeguard | ||
| (w/ dual meter display) | M2 Performance | 500 |
| Bosch in-tank fuel pump | ||
| MazdaComp aluminum radiator | M2 Performance | 617 |
| Red silicone vacuum hoses (ty-wrapped) | KDRotary (B&B) | 210 |
| GoodRidge silicone radiator hoses | KDRotary (B&B) | 260 |
| Aluminum AST | Tri-Point Engineer | 130 |
| CWC Oil Cooler Kit | CWC | 700 |
| Bell Electronics RRFPR (rising rate fuel pressure regulator) | ||
| Electronic mods: | ||
| VDO center column boost gauge (PSI) | Pettit Racing | |
| SPA dual digital guages for oil temp / oil pressure and water temp / fuel pressure | ||
| GReddy turbo timer | Rotary Performance | 105 |
| PIAA Superwhite 90-100W headlight bulbs | KDRotary | 40 |
| Ground Kit | KDRotary | |
| Valentine One --radar detector | ||
| Exhaust mods: | ||
| PFS 3" SS catback exhaust w/ 4" tip | Peter Farrell | |
| Bonez 3" SS downpipe w/ Exhaust gasket kit | Rotary Performance | 353 |
| Pettit midpipe w/ silencer | Pettit Racing | 300 |
| Heated O2 Sensor | KDRotary | 22 |
| Suspension mods: | ||
| Mazdaspeed coil overs (4) | ||
| Cusco front and rear strut support bars | Dante Hernandez | 300 |
| Trak Pro Launch Kit | Pettit Racing | 300 |
| CWC Sway Bar Mounts | CWC | 325 |
| HKS Pillow Mounts | Wael Dasher | 250 |
| Mandeville big brake kit | ||
| Wheel/Tire and Exterior: | ||
| Konig Villains alloy wheels 17x9 | ||
| Kuhmo Victors 255x40x17 | ||
| Package Price | JoTechMotorsports | 1840 |
| MazdaSpeed Shortshift Kit | Rotary Performance | 264 |
| GoodRidge SS brake lines | GoodRidge | 80 |
| Tony D floor mats | Rotary Performance | |
| Mazda F&R Mudguards | Gallery Mazda | 136 |
| Shop Manual | Gallery Mazda | 50 |
| Zaino Bros Show Car Polish Products | Zaino Brothers | 195 |
| Mazda 99 J-spec round tail lights | ||
| 99 J-spec nose, 15th anniv hood and mazdaspeed rear spoiler | ||
| Labor: Dave Barninger (KD Rotary) of PA and Dana Salb from Peabody, MA | ||
| Future Mods | ||
| custom paint job (viper eater) | ||
| RB Adjustable sway bars | ||
| Street-ported and balanced engine | ||
| ported wastegate | ||
| balanced ball bearing turbos | ||
| 4.30 final drive and pinion set (Rx7 RZ spec) | ||
| RE Amemiya light kit |